![]() Subscribe to our weekly e-newsletters, follow us on LinkedIn, Twitter, and Facebook, and check out our eBook archives for more applicable, expert-informed connectivity content. Like this article? Check out our other Meet the Connector and our Sensors and Antennas Page, and o ur 2022Article Archive. Consumer electronics (white and brown goods), computer equipmentĪllied Electronics, Digi-Key Electronics, Newark, TE Connectivity Related products: With the fans what you do is plug the red and black wires that go to the big molex connector into the peripheral power connector from the power supply and if there is a yellow or blue wire with a small connector that connects to the motherboard.Today, the connector is a standard power. These connectors are often available in low halogen or halogen-free versions, especially in those used in appliances. The P4 connector is a 12V power supply cable used with motherboards that have an Intel Pentium 4 or later processor.Certifications: CSA, TUV, UL (94V-40 for flammability) Molex offers a wide variety of wire-to-board connector types that fit applications requiring high-power, microminiature, sealed, rugged, and reliable.In a four-pin variant, the fourth lead is a control lead in a fan application, it would control the speed of the fan. Pins: The leads in a 3-pin connector are designated for power, signal, and ground.So if this is the case, you could take 5v from a usb header on the motherboard and connect it to all the "detect" pins on the motherboard to make it think all molex headers have molex connectors in them.TE Connectivity’s AMP MTA Connectors, from Mouser Electronics Design Notes Notice they say DETECT where normally in a molex connector is 5v - so I would guess they simply check if there's 5v on that pin to figure out if you plugged a molex connector or not. ![]() In the second scenario, with a single video card you could plug the molex connector in any molex header and it wouldn't matter. In the first scenario, if you install a single video card, you would only need to connect a molex for that slot or pair of slots. ![]() The motherboard will most likely only do a "Is voltage present in the molex connectors? " check and won't actually measure how much power comes through connector. If the motherboard requires all molex connectors to be connected to the power supply or it won't start, then you could "hack it" to think you plugged the connectors. Most gaming PC include these multiple fan headers, while others only have a single header. These headers are located near the CPU socket in most motherboards. The motherboard has a 4-pin or 3-pin connector for the CPU and Case fans. But if the motherboard is designed in such a way that the pci-e slots only get power from molex connectors (which would be dumb) then you would have to plug at least one molex connector in the motherboard. Yes, fan power is directly connected to the motherboard. If you have a single video card in the motherboard, you could probably be fine without any molex connectors, because the slot would receive power from the 24 pin connector. each molex adds around 50 watts to those 200 watts. That's why the motherboard added those molex connectors, to ADD some power on top of what's available through the 24 pin connector(s') 12v wires. The motherboard can give the pci-e slots some power from the 24 pin connector (there's around 150-200w available there, 2 12v wires, each good for around 9A, so 18A x 12v = 216w, but some of that goes to fan headers, maybe some onboard stuff) but if you install 4-6 video cards and each takes 60 watts, you're looking at 240-360 watts taken from pci-e slots. I'd be fine doing 50-55w on molex connectors.Ī video card is allowed to take as much as 75w from a pci-e slot : 10w on 3.3v and 65w on 12v. The maximum rating of a single molex connector is 5A per voltage (so 5A on 12v, 5A on 5v ). so in theory a sata connector can do 12v x 4.5 = 54w. The maximum rating of SATA is 4.5A (3 contacts for each voltage x 1.5A per contact = 4.5A). Wouldnt it be bad to use sata to molex because the molex port might take 75W but sata has like 60 or 65 W ? Of course don't actually use such adapter cables to actually use multiple video cards on the board. If the motherboard really wants all molex connectors to be "populated" you can also buy adapters that convert one molex or one sata into 2 molex connectors. The extra molex connectors would be to provide additional power to the pci-e slots, because otherwise all pci- slots would be powered from just 2 12v wires in the 24 pin connector. ![]() Try turning on the motherboard with just the 24 pin connector and the cpu 4/8 pin connector. It's common for a cable to have 3-4 connectors, usually 2-3 sata and a molex connector. Your beQuiet power supply has "peripheral" connectors on it, in which you can plug cables that have a bunch of connectors.
0 Comments
Leave a Reply. |